Design Summary
Bandpassfilter using coupled lineMicrostripline
Implementation of L, C with Width & Length
Bandpass Fillter
IMT-2000 frequency bandwidth between 2.25 GHz and 2.75 GHz
Chebychev Filter
Sharp skirt characteristic
Design Procedures
Using two different equal-ripple
0.5 dB : High insertion loss
0.2 dB : More improved Insertion loss
A filter is widely used in overall RF system. There are many species and structures in filter. A filter seems to be simple, but there are many considerations to designfilter. In this paper, we designmicrostripbandpassfilter which has bandwidth of 500 MHz and center frequency of 2.5 GHz. Alumina is used as substrate, and chromium is used as conductor. Final results are achieved as follows. Ins
hairpin resonator and applies it to the design of an X-band
oscillator. The measurement of the resonator itself shows that the
suggested resonator provides a higher loaded quality factor with
reduced circuit area compared to the conventional hairpin
resonator. The oscillators are designed to operate at 9.2 GHz
using the conventional and novel hairpin resonators, to compare
the phase noise p
흐르는 현상. 이러한 현상으로 인하여 많은 전류의 손실이 생기게 된다.
라는 현상 때문에 일반 도체 Wire를 쓸 수 없게 됩니다. 따라서 마이크로파 영역의 주파수를 다루는 회로에는 일반 Transmission Line이 아닌 특수한 Transmission Line이 쓰이게 되는데, 이러한 Transmission Line을 “MicrostripLine”이라고 한다.
, 신호를 증폭시킨다면 신호뿐만 아니라 noise도 증폭될 것이다. 그래서 우리는 noise를 필터링해야 하며, 이 역할을 해주는 것이 Low Noise Amplifier 이다. LNA를 사용함으로서 bad channel상태에서의 수신된 신호를 검출할 수 있게 된다. 따라서 우리는 이 보고서를 통해 LNA를 설계하는 방법을 설명할 것이다.
frequency tuning range of 11.15 MHz
with the output power flatness less than 0.10 dB at
the center frequency of 8.836 GHz. The
fundamental output power was 12.34 dBm and the
second harmonic was suppressed by 32.04 dBc,
and the phase noise performance was 95.78
dBc/Hz at 100 kHz offset.
Index Terms- GaAs MESFET, microstrip hairpin
resonator, oscillator, phase noise.
1. 서 론
압전 재료는 기계적 에너지를 전기적 에너지로 변환시키는 압전 직접효과(piezoelectric direct effect)와 전기적 에너지를 기계적 에너지로 변환시키는 압전 역효과(piezoelectric converse effect)를 갖는 기능성 세라믹스를 지칭한다. 간단한 형상을 가지며 소형화가 가능한 압전체는 초음파 모터, 압전
1. 실험목적
- 저항기의 여러 가지 종류와, 표시된 저항 값을 해석하는 법을 배운다.
- 저항계로 저항을 측정하여 운용 법을 익히며, 표시된 저항 값과 비교해 본다.
- 가변저항기의 여러 조건에 따른 저항을 측정하여 작동원리를 이해한다.
2. 원리 및 배경지식
(1) 저항기
저항기는 전기전류의 흐름을
Filtering된 출력을 저압제어 발진기의 주파수 조정 포트에 인가하게 된다. 따라서 PLL action에 따라 channel의 정수 배에 해당하는 주파수 TCXO 정도의 주파수 안정도를 지니게 되고 이동통신 주파수 대역에 있는 다수의 channel 중 digital 입력에 따라 원하는 channel을 선정할 수 있는 국부 발진원으로 사용할 수
coupler)를 서로 연결하여 구현할 수 있으며, 대부분 평면 구조의 마이크로 스트립 형태로 마이크로 스트립 대 슬롯 선로(slot line) 결합 구조, CPW 대 슬롯라인 결합 구조, CPW 대 CPW 결합 구조를 이용한다. 마이크로스트립의 경우 큰 분산 효과로 인하여 고주파에서 일정한 특성 임피던스 유지가 어려워 광대